Collars and Necklines – SS2 Fashion and Garment Making Lesson Note (First Term)
Lesson note at a glance
- Class
- SS2
- Subject
- Fashion and Garment Making
- Term
- First Term
- Reading time
- 6 min
A neckline is the finished edge around the neck of a garment, and a collar is an extra piece of fabric attached to that edge.
Behavioural objectives
- Name and describe five common types of neckline.
- Explain why a neckline must be stay-stitched straight after cutting.
- Finish a neckline without a collar, using bias binding or a facing.
- Group collars into flat, standing and rolled collars, with an example of each.
- Sew a Peter Pan collar by following the correct steps.
- State the order of work for attaching a shirt collar.
What is a neckline?
A neckline is the shape of the finished edge of a garment where it sits around the neck.
- Base for the collar: the neckline must be cut and handled well before any collar is added.
- Shape: the neckline is cut as a curve or an angle, so part of its edge lies on the bias.
What are the common types of neckline?
Five common necklines are the round neck, V-neck, sweetheart, square neck and boat neck.
- Round neck: the most basic style, used for T-shirts and simple blouses.
- V-neck: a “V” shape that makes the neck look longer and slimmer.
- Sweetheart neckline: shaped like the top of a heart, popular for bridal and Aso-Ebi styles.
- Square neck: a square shape that gives a structured, vintage look.
- Boat neck (bateau): a wide neckline that runs straight across the collarbone.
Why must a neckline be stay-stitched?
Stay-stitching is a single line of straight stitches sewn just inside the seam line to stop the edge stretching.
- Bias edge: part of a curved neckline lies on the bias, which stretches very easily.
- Fit: a stretched neckline will not fit the collar or lie flat on the body.
- Timing: stitch immediately after cutting, before the pieces are handled much.
Steps for stay-stitching
- Cut out the neckline.
- Use a normal straight stitch, on the single layer of fabric.
- Sew just inside the seam line, within the seam allowance.
- Sew from the shoulder towards the centre, without pulling the fabric.
How do you finish a neckline without a collar?
A neckline without a collar is finished with bias binding or a facing so that the raw edge does not fray.
Method 1: What is bias binding?
Bias binding is a strip of fabric cut diagonally across the grain, so that it bends round curves.
- Use: it wraps around the raw edge and is good for armholes and simple round necks.
- Advantage: it stretches enough to follow a curve without puckering.
Method 2: What is a facing?
A facing is a piece of fabric cut to the same shape as the neckline and turned to the inside of the garment.
- Cut the facing in the same shape as the neckline.
- Sew it to the neckline with right sides together.
- Trim the seam allowance and clip the curves.
- Under-stitch the facing.
- Turn the facing to the inside and press.
Two tips for facings
- Clipping: make tiny snips into the seam allowance of the curves, without cutting the stitching. This lets the fabric spread and lie flat.
- Under-stitching: sew the seam allowance to the facing, close to the seam. This keeps the facing inside so it does not show while the person walks.
How do bias binding and facing compare?
| Feature | Bias binding | Facing |
|---|---|---|
| Material | Narrow bias strip | Shaped piece matching the neckline |
| Edge shows on the outside? | Yes, unless turned fully inside | No, it lies inside |
| Best used for | Armholes and simple round necks | Necklines of many shapes |
What is a collar?
A collar is an extra piece of fabric attached to the neckline, to keep the neck warm or to decorate the garment.
What are the categories of collar?
There are three main categories of collar: flat, standing and rolled.
- Flat collars: lie flat against the garment, as in the Peter Pan collar seen on school uniforms and vintage dresses.
- Standing collars: stand up straight around the neck, as in the Mandarin (Chinese) collar.
- Rolled collars: stand up at the neck first and then fold over, as in the standard shirt collar.
Why is interfacing used in a collar?
Interfacing is a stiffener fixed to the wrong side of fabric to give a collar shape.
- Shape: it keeps the collar crisp and sharp.
- Durability: a collar without it looks floppy and tired after a few washes.
What tools are needed to sew a collar?
- Interfacing: the stiffener for the collar pieces.
- Scissors and pins: for cutting, trimming, clipping and holding pieces together.
- Iron: for fixing the interfacing and pressing edges.
- Turning tool: a blunt tool or a dull pencil to push out edges and corners.
How do you sew a flat collar (Peter Pan)?
A Peter Pan collar is a flat collar with no stand, so it is the easiest collar for a student to start with.
- Interfacing: iron the interfacing onto the wrong side of one collar piece.
- The sandwich: place the two collar pieces with right sides together (pretty sides facing).
- The curve: sew around the outer edge and leave the neck edge open. Use a small stitch length on the curves so they are smooth.
- Trimming: trim the seam allowance close to the stitches and clip the curves. This stops bulk at the edges.
- Turning: turn the collar right side out and push out the edges with a turning tool.
- The press: press the collar flat until the edges are crisp.
How do you sew a shirt collar?
A shirt collar is a rolled collar made of two parts, the collar leaf and the collar stand.
- Collar leaf: the upper part that folds over and shows.
- Collar stand: the narrow band that rises from the neckline and supports the leaf.
What is the order of work for a shirt collar?
- Prepare the leaf: sew, trim, turn and press the leaf like the Peter Pan collar.
- Attach the stand: sandwich the finished leaf between the two stand pieces and stitch.
- Finish the stand: trim, turn out and press the stand.
- Join to the shirt: match the centre back of the collar to the centre back of the neck. Pin carefully to the front edges.
- Stitch the neckline seam: sew the stand to the neckline and press the seam.
- Top-stitch: sew slowly, because this line shows and must be perfectly straight.
What common faults occur in collars?
- Collar too short for the neck: the neckline was probably stretched while sewing. Stay-stitch next time.
- Blunt corners: not enough fabric was trimmed from the corners before turning.
Evaluation
- Name five common types of neckline.
- Why should a neckline be stay-stitched immediately after cutting?
- Describe two ways of finishing a neckline without a collar.
- Name the three categories of collar and give one example of each.
- List the steps for sewing a Peter Pan collar.
Assignment
Class task: Look at three different necklines on your classmates’ outfits today. Name each neckline and say whether it is finished with a facing or with binding.
Teacher's lesson plan
A ready-to-use lesson plan for this topic: objectives, previous knowledge, materials, step-by-step presentation, board summary and conclusion.
Included when you get this note, and inside your download. Sign in with your purchase to see it here.
Sign inThis term's Fashion and Garment Making topics
SS2 First Term · 6 topics

