Software Flashing – SS2 Computer Hardware & GSM Repair Lesson Note (Second Term)
Lesson note at a glance
- Class
- SS2
- Subject
- Computer Hardware & GSM Repair
- Term
- Second Term
- Reading time
- 6 min
Flashing is the process of deleting a phone’s old or broken Android operating system and installing a fresh, clean version.
- Effect: it wipes the phone’s memory, like formatting a computer or re-installing Windows.
- Requirements: the correct firmware, the right drivers and a flashing tool that matches the phone’s chip.
Behavioural objectives
By the end of the lesson, students should be able to:
- explain what flashing is and when a phone may need it;
- name the three things needed before flashing a phone;
- match MediaTek (MTK), Spreadtrum (SPD) and Samsung phones to the correct flashing tool;
- list the steps for flashing a phone safely;
- state the cause and fix of common flashing errors.
What is flashing?
Flashing is the process of replacing a phone’s old or damaged Android operating system with a fresh, clean copy.
- Operating system (OS): the main software that runs the phone, such as Android.
- Memory wipe: flashing clears the phone’s memory and gives it a new “brain”.
- Comparison: it works like formatting a computer or re-installing Windows.
When does a phone need flashing?
A phone needs flashing when a software fault cannot be fixed by simpler methods.
- Stuck on logo: the phone shows the brand logo and never reaches the home screen.
- Bootloop: the phone restarts again and again without starting fully.
- Very slow phone: the phone hangs and is slow even after clearing apps.
- Repeated app errors: messages such as “Unfortunately, App has stopped” keep appearing.
- Failed update: the phone will not start properly after an update stops halfway.
What three things do you need to flash a phone?
You need three things to flash a phone: the firmware, the drivers and the flashing tool.
- If one of the three is missing, the process will fail.
1. The firmware (the “OS”)
- Firmware: the actual Android software file, often called a Stock ROM.
- Exact match: you must use the version made for the exact model of the phone.
- Example: software for a TECNO Spark 5 Pro can damage a TECNO Spark 7.
2. The drivers (the “translator”)
- Driver: a small piece of software that lets the computer recognise and talk to the phone’s chip.
- Why needed: without it, the computer does not know how to talk to the phone when it is plugged in.
- VCOM drivers: used for MTK chips.
- SPD drivers: used for Spreadtrum chips.
3. The flashing tool (the “injector”)
- Flashing tool: the computer program that pushes the firmware into the phone.
- SP Flash Tool: used for phones with MediaTek (MTK) chips.
- SPD Upgrade Tool: used for phones with Spreadtrum (SPD) chips.
- Odin: used for Samsung phones.
How do you identify the chipset (MTK vs SPD)?
The chipset is the main processor “engine” inside the phone, and it decides which flashing tool you must use.
- You cannot use the wrong tool for the wrong chip.
- Find the phone’s exact model, then check its specifications to see the chipset.
MediaTek (MTK)
- Found in: most Infinix and TECNO phones and some older Huawei phones.
- Tool: SP Flash Tool.
Spreadtrum (SPD)
- Found in: many budget or small Android phones and itel devices.
- Tool: SPD Upgrade Tool.
Qualcomm
- Found in: many mid-range and high-end phones, including some Xiaomi and Redmi models.
- Tool: QFIL or MiFlash, depending on the phone.
- Samsung: Samsung phones are flashed with Odin, whichever chip they use.
What are the steps for flashing a phone safely?
There are five main steps: back up, charge, load the scatter file, connect the phone and watch the progress bar.
- Backup: flashing wipes everything (photos, contacts, messages). Tell the customer their data will be gone.
- Charge the battery: never flash a phone with less than 50% battery. If it dies halfway, it may become a “brick”, a phone that will not turn on.
- Load the scatter file: in the flashing tool, click “Choose” and select the scatter file, a text file that tells the tool where to put each part of the software.
- Connect the phone:
- Turn the phone completely off.
- Hold the “Volume Down” or “Volume Up” button (the boot key).
- Plug in the USB cable.
- Watch the progress bar: a red bar appears, then a yellow bar. Do not touch the cable until a green “Success” circle appears.
What should you do after flashing?
- Wait for the green “Success” circle.
- Unplug the USB cable.
- Switch the phone on. The first start can take several minutes, so be patient.
- Set up the phone and check that calls, network and Wi-Fi work.
What are the common flashing errors and their fixes?
Most flashing errors come from a bad cable, missing drivers or leftover old data.
- “BROM Error: S_FT_DOWNLOAD_FAIL”: often caused by a bad USB cable or loose port. Try a different cable and port.
- Phone stuck at 0%: the drivers are not installed correctly. Re-install the VCOM drivers.
- Bootloop (still stuck on logo): old cache may remain. Go into “Recovery Mode” and choose “Wipe Data/Factory Reset”.
- Phone does not start after flashing: the firmware may be wrong for that model. Check the model and use the correct firmware.
Which flashing tool and file does each phone use?
| Phone brand / chip | Flashing tool | Key file type |
|---|---|---|
| TECNO / Infinix (MTK) | SP Flash Tool | .txt (scatter file) |
| itel / small Androids (SPD) | SPD Upgrade Tool | .pac file |
| Samsung | Odin | .tar or .md5 files |
| Qualcomm phones (for example some Xiaomi / Redmi) | QFIL / MiFlash | XML files |
Why is flashing the “last resort”?
Flashing is the last resort because it erases all data and a wrong file can ruin the phone.
- First try a hard reset: use the recovery key combination for the model (often Volume Up + Power). The keys differ between phones.
- Then flash: only if the hard reset does not fix the problem.
- Risk: one wrong file can brick a phone.
What is the difference between a soft brick and a hard brick?
- Soft brick: the phone is stuck on the logo or in a bootloop but still responds, so it can usually be reflashed.
- Hard brick: the phone shows no sign of life and will not turn on. It may need special repair.
| Feature | Soft brick | Hard brick |
|---|---|---|
| Phone behaviour | Stuck on logo or bootloop | Completely dead |
| Fix | Usually reflash or factory reset | Needs special repair |
Evaluation
- What is flashing?
- Name the three things you need before you can flash a phone.
- Which flashing tool is used for a phone with an MTK chip? Which is used for an SPD chip?
- Why should a phone have at least 50% battery before flashing?
- A phone is stuck at 0% during flashing. What is the likely cause, and what should you do?
Assignment
Write a short guide titled “Flashing: the last resort” that lists the five safe flashing steps in your own words, says what to try before flashing, and includes a table giving the flashing tool and key file type for TECNO / Infinix, itel and Samsung phones.
This term's Computer Hardware & GSM Repair topics
SS2 Second Term · 8 topics

