Skip to content

Revision of Major Skills – SS3 Fashion and Garment Making Lesson Note (Second Term)

Lesson note at a glance

Class
SS3
Subject
Fashion and Garment Making
Term
Second Term
Reading time
8 min
Start of this note, 1 of 7
Take this term’s notes offline
Reading here is free. Download all 7 SS3 Fashion and Garment Making Second term notes as PDF to print and Word to edit.
Download all three terms, ₦2,000
Instant download. Secure payment by Paystack. Card, bank transfer, USSD or OPay. Payment stuck? WhatsApp us.

Revision of major skills is the review of the basic steps that make a garment fit well and look neat.

What are the major skills in garment making?

There are six major skill areas to revise: measuring, cutting, seams, fullness, collars and sleeves, and fasteners with finishes.

Advertisement
  • Measuring and cutting: taking correct measurements and cutting along the grain.
  • Seams: joining and neatening pieces so they are strong and flat.
  • Fullness control: using darts, gathers and pleats to shape flat cloth to the body.
  • Facings, sleeves and collars: the parts people see first, so they must look sharp.
  • Fasteners: zips and other closings that must work smoothly.
  • Finishes: hems, thread clipping and the final press.

Behavioural objectives

By the end of the lesson, students should be able to:

  1. state the key measurements to check and explain why ease is added;
  2. explain why grainline and a consistent seam allowance matter when cutting and sewing;
  3. describe how to sew and finish a plain seam and a French seam;
  4. explain how darts, gathers and pleats control fullness;
  5. describe how to treat facings, sleeves and collars neatly;
  6. name the types of zip and hem, and say how to give a garment a good final press.

Why are measuring and cutting the foundation of garment making?

Measuring and cutting are the foundation because a wrong measurement cannot be corrected by good sewing.

Which measurements should you check?

  • Across-back: the width of the back between the two armholes.
  • Bust point: the position of the fullest part of the bust, used to place bust darts.
  • Hip depth: the distance from the waist down to the fullest part of the hips.
  • Other basics: bust, waist, hip, shoulder, garment length and sleeve length.

What is ease?

Ease is the extra room added to body measurements so the wearer can breathe, move and sit comfortably.

  • Wearing ease: the small extra amount that stops the garment being tight on the body.
  • Design ease: extra room added for style, as in a loose gown or a flared skirt.
  • No ease: seams strain and may burst when the customer sits down.
Advertisement

What is cutting discipline?

Cutting discipline means cutting along the grain and keeping seam allowances equal.

  • Grainline: the direction of the lengthwise threads in the cloth. Place pattern pieces along it.
  • Off-grain cutting: the garment twists on the body, especially after the first wash.
  • Seam allowance: the extra cloth between the cutting line and the stitching line.
  • Consistency: if you use 1 inch for the sides, use 1 inch throughout the garment.

How do you sew and finish seams?

A seam is a line of stitches that joins two pieces of cloth, and it must be strong and neat.

What is a plain seam?

A plain seam is the most common seam, sewn with the right sides of the cloth together.

  1. Place the right sides together and pin along the seam line.
  2. Stitch with the correct seam allowance.
  3. Neaten the raw edges.
  4. Press the seam open so it lies flat.

What is a French seam?

A French seam is a seam that encloses the raw edges inside, used on thin or see-through fabrics such as chiffon and silk.

  1. Place the wrong sides together and stitch a narrow seam.
  2. Trim the seam allowance close to the stitching.
  3. Press, then fold along the stitched line so the right sides face each other.
  4. Stitch again, just wide enough to enclose the trimmed raw edges.
  5. Press the seam to one side.

How do the two seams compare?

Feature Plain seam French seam
First stitching Right sides together Wrong sides together
Number of stitching lines One Two
Raw edges Visible inside, so they need neatening Hidden inside the seam
Pressing Pressed open Pressed to one side
Best fabric Most fabrics Thin, see-through fabrics

How do you finish raw edges?

Neatening is the treatment of raw edges to stop the cloth from fraying.

  • Overlocking: an overlock machine trims and wraps the edge in thread.
  • Zigzag stitch: a row of zigzag stitches along the raw edge on an ordinary machine.
  • Bias binding: a strip of cloth cut on the bias and folded over the raw edge.
  • Why it matters: the inside of the dress looks as good as the outside and lasts longer.
Advertisement

How do you control fullness with darts, gathers and pleats?

Fullness control is the shaping of flat fabric to fit the curves of the body using darts, gathers and pleats.

What are darts?

A dart is a folded wedge of cloth stitched to a point to take fabric in at the waist or bust.

  1. Mark the dart legs and the point on the wrong side.
  2. Fold the dart with right sides together and pin.
  3. Sew from the wide end towards the point.
  4. Do not backstitch at the point. Leave thread ends and tie a small knot.
  5. Press bust darts downwards and waist darts towards the centre.
  • Why no backstitch: it makes a lump at the point that shows on the chest.

What are gathers?

Gathers are small, even folds made by pulling up long stitches to reduce the width of a piece of cloth.

  1. Sew two rows of long machine stitches along the edge, without backstitching.
  2. Pull the bobbin threads gently to form even bunches.
  3. Spread the gathers evenly to fit the waistband or sleeve edge.
  4. Pin, then stitch the gathered edge in place.
  • Common mistake: letting all the gathers bunch up in one spot.

What are pleats?

Pleats are folds of cloth pressed flat and held in place at the top.

  • Knife pleats: all folds face the same direction.
  • Box pleats: two folds face opposite directions to make a flat box shape.
  • Making them neat: press the pleats crisp and pin them before taking them to the machine.

How do you sew facings, sleeves and collars?

Facings, sleeves and collars are the parts people see first, so they must be sharp and smooth.

What are facings and interfacing?

A facing is a shaped piece of cloth that finishes a raw edge such as a neckline or armhole.

  • Interfacing: a stiffening layer put on necklines and collars to stop sagging or stretching.
  • Understitching: sewing the seam allowance to the facing, close to the seam.
  • What understitching prevents: the facing rolling out and “peeping” when the dress is worn.
Advertisement

How do you set a sleeve?

A set-in sleeve should fit the armhole smoothly with no tucks at the shoulder.

  1. Sew a row of long stitches around the sleeve head (top curve).
  2. Pull the thread slightly to ease the extra cloth in.
  3. Pin the sleeve into the armhole, matching the notches and shoulder point.
  4. Stitch and press the seam towards the sleeve.
  • Exception: a puff sleeve is meant to have gathers at the sleeve head.

How do you make a sharp collar?

  1. Sew the collar pieces with right sides together, leaving the neck edge open.
  2. Trim the excess cloth at the corners with small scissors.
  3. Turn the collar right side out and push the corners out gently.
  4. Press the edges flat.

Which fasteners and final finishes does a garment need?

Fasteners and final finishes are the small details that make a garment work and look complete.

What are the types of zip?

There are three common types of zip: centred, lapped and invisible.

Type of zip How it looks Common use
Centred zip Seam closes over the middle of the zip, teeth hidden under two folds Centre back of dresses and skirts
Lapped zip One side overlaps the zip, hiding the teeth Side of skirts
Invisible zip Teeth hidden inside the seam, so only a seam line shows Fine dresses and skirts

What are the types of hem?

The hem is the finished bottom edge of a garment, and the two common types are the blind hem and the machine hem.

  • Blind hem: hand-sewn with small stitches so no thread shows on the outside. Use it for high-quality work.
  • Machine top-stitched hem: quick and strong, suitable for casual wear. The stitching must be perfectly straight.

How do you give a garment a final press?

The final press is the last pressing and checking that removes wrinkles and gives the garment a clean finish.

Advertisement
  1. Clip all loose threads.
  2. Check that every seam, zip and hem is in place.
  3. Give the whole garment a final steam or press.
  4. Let it cool and settle before packing or handing it over.

Which habits should students correct during revision?

Revision is the time to correct bad habits by returning to the basics.

  • Measure twice, cut once: check measurements before you cut.
  • Press every seam: press as you sew, not only at the end.
  • Finish properly: never rush neatening, hems and the final press.

Evaluation

  1. Name three measurements you should double-check, and say why ease is added.
  2. What happens to a garment that is cut off-grain?
  3. For which type of fabric is a French seam used, and how is it sewn?
  4. How should a dart be started and ended, and why should you not backstitch at the point?
  5. What is understitching, and what does it prevent?

Assignment

Write a short note on how to finish a garment after the main sewing is done. Include the types of zip, the types of hem and the steps of the final press.

This term's Fashion and Garment Making topics

SS3 Second Term · 7 topics

  1. Revision of Major Skills
  2. SSCE Past Questions: Theory
  3. SSCE Past Questions: Practical
  4. Mock Project I
  5. Mock Project II
  6. Mock Project III
  7. Exam Prep and Coaching
Advertisement

Lesson Notes for Other Classes

Print it or edit it in Word

Every note is free to read online. A PDF or Word copy of one subject costs ₦1,000 for one term, or ₦2,000 for all three terms.

Sign in first, then choose your class and subject at checkout.